Juniper SRX3400 Hardware Manual Download Page 81 | Manualshive

Page: 81 / 232

Juniper SRX3400 Hardware Manual Download Page 81

NOTE:

The same AC power supply is used in both the SRX3400 and SRX3600

Services Gateways. However, this power supply is not interchangeable with
that used in the SRX1400 Services Gateway. The SRX1400 Services Gateway
power supply will fit into the SRX3400 Services Gateway, but will not work
properly. You can identify the SRX1400 Services Gateway power supply by
the plastic air filter assembly installed over the cooling air inlet as shown in

Figure 34 on page 67

.

Figure 34: Identifying Power Supply Types

g036110

Air filter

SRX3400 and SRX3600 DC Power Supply

SRX3400 and SRX3600 AC Power Supply

SRX1400 DC Power Supply

SRX1400 AC Power Supply

To install an AC power supply:

1.

Attach an ESD grounding strap to your bare wrist and connect the strap to one of the
ESD points on the chassis. For more information about ESD, see

“Preventing

Electrostatic Discharge Damage to the SRX3400 Services Gateway” on page 145

.

2.

Orient the power supply so that the locking lever is on the left, as shown in

Figure 35 on page 68

.

67

Copyright © 2013, Juniper Networks, Inc.

Chapter 6: Installing Additional Components in the SRX3400 Services Gateway

«
...
79
80
81
82
83
...
»

Summary of Contents for SRX3400









































































































































































































































Reviews:

No comments