Juniper SRX3400 Hardware Manual Download Page 24

Page: 24 / 232

Table 5: Available SRX3400 Services Gateway Hardware
Components

(continued)

Minimum/Maximum

Hardware Component

Up to 6 allowed (see note below)

Network Processing I/O Cards (NP-IOCs)

1 required, 2 allowed

Network Processing Cards (NPCs)

1 required, up to 4 allowed

Services Processing Cards (SPCs)

1 required, up to 2 allowed

Power supply

1 required

Fan tray (containing multiple fans)

NOTE:

A minimum configuration must include one SPC and either one NPC

or one NP-IOC. However, if there are no NPCs in the chassis, the Ethernet
ports on the SFB will not be functional. See

“SRX3400 Services Gateway

Network Processing Cards” on page 20

“SRX3400 Services Gateway

NP-IOCs” on page 22

, and

“SRX3400 Services Gateway Services Processing

Cards” on page 20

for details about these cards.

SRX3400 Services Gateway Hardware Guide

Summary of Contents for SRX3400






















































































































































































































Search results

Summary of Contents for SRX3400

Reviews:

Juniper SRX3400, Hardware Manual, Page: 24 / 232

Search results

Summary of Contents for SRX3400

Reviews: