ITT Industries PumpSmart PS200 Configuration & Operation Manual Download Page 14 | Manualshive

Page: 14 / 159

background image

PS200 Configuration & Operation Guide

SINGLE PUMP PROCESS

Page 12

ID MAGN REQ

This warning is normal, proceed on to the step

INDENTIFICATION RUN

IDENTIFICATION RUN

PumpSmart uses specific motor detail to create a mathematical
motor model. This model enables more accurate motor control
and is created with the motor data you have just entered and by
magnetizing the motor for 20 to 60 seconds at zero speed. This is
called a First Start ID Run.

Once all the motor data has been entered, the following warning
will be displayed:

ID MAGN REQ

This warning indicates that a First Start ID Run is required before
the pump may be operated. Now is a good time to perform this
run.

With the motor connected to the drive and the keypad in Local (L)
mode, press the START button. FOLLOW ALL STANDARD SAFETY
PRACTICES FOR STARTING MACHINERY.

NOTE
ALLOW THE FIRST START ID RUN TO COMPLETE BEFORE
STOPPING/RESETTING THE DRIVE. Although the motor may not
appear to respond to the start command, it has. A warning
message “ID MAGN” will be displayed during the ID. Once the ID
run is complete, the message "ID DONE" will be displayed.

NOTE - If the motor is changed in the future, a First Start ID Run
must be performed again to maintain the accuracy of the
PumpSmart control.

Once the First Start ID Run has been completed, the following
message will appear:

ID DONE

Once this appears, proceed on to the next step DRIVE OPERATION
LIMITS.

E-Stop/Permissive

The PS200 will not operate unless
the E-Stop/Permissive switch [DI1L]
is closed. This includes performing
the First Start ID Run. If not closed
a warning message will appear on
the keypad display:

R U N D I S A B L E D

See Appendix A-4, Instrument
Wiring, for details on wiring this
switch.

NOTE:
The E-Stop/Permissive switch can not
be defeated through parameter
setting. If your application does not
use an E-Stop / Permissive switch, DI1L
can be bypassed physically inside the
PumpSmart unit. Refer to Appendix A-
4, Instrument Wiring, for details.

«
...
12
13
14
15
16
...
»

Summary of Contents for PumpSmart PS200
































































































































































Reviews:

No comments

Related manuals for PumpSmart PS200

Brand: YASKAWA Pages: 5

Brand: BINZEL-ABICOR Pages: 108

MFORCE MICRO DRIVE Plus MICROSTEPPING

Brand: IMS Pages: 64

Brand: ABB Pages: 20

Brand: Yamaha Pages: 24

CRW4416E - CRW - CD-RW Drive

Brand: Yamaha Pages: 25

CRW4416S - CRW - CD-RW Drive

Brand: Yamaha Pages: 26

Brand: Yamaha Pages: 15

Brand: Yamaha Pages: 24

CRW8824FXZ - CD ROM Drive

Brand: Yamaha Pages: 44

PORTATONE KB-280

Brand: Yamaha Pages: 47

CRW8824SX - CRW 8424SX - CD-RW Drive

Brand: Yamaha Pages: 46

CRW8424SX Series

Brand: Yamaha Pages: 46

CRW8424E Series

Brand: Yamaha Pages: 46

CRW3200SX Series

Brand: Yamaha Pages: 46

CRW3200UX Series

Brand: Yamaha Pages: 48

CRW2200UX Series

Brand: Yamaha Pages: 45

CRW3200IX Series

Brand: Yamaha Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands