Home
/
Instramed
/
CardioMax
/
User Manual

Instramed CardioMax, User Manual

Share

Page: 95 / 205

Instramed CardioMax User Manual Download Page 95

User manual |

AED mode

95

AUDITIVE INFORMATION SIGNAL (BEEP)

DESCRIPTION

Metronome for CPR compressions

The equipment beeps at a frequency of 100 beeps

per minute, helping the user in performing the cardiac

compressions.

The equipment also has verbal information signals. The differentiation of verbal

infor-mation signals and verbal alarm signal is given in two ways:

Sound power:

Verbal information signals will always be at least 6dB(A) below the set to the alarm

signal.

Messages content:

Verbal information signals have the following messages:
•  Analyzing heart rhythm.
•  Perform CPR for two minutes.
•  Treatment recommended – do not touch the patient.
•  Shock is not recommended.
•  Put the paddles on the patient’s chest.
•  Energy is being discharged internally.
•  Don’t touch the patient
•  Children's paddles.
•  Treatment successfully
•  Give two breaths
•  Check the patient reparation or pulse if you cannot detect either, perform CPR for

two minutes.

«
...
93
94
95
96
97
...
»

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands