manualshive.com logo in svg

Instramed CardioMax, User Manual

Share
Download
Instramed CardioMax User Manual Download Page 3

ATTENTION: Observe the battery charge maintenance instructions

First use:

Before using the CardioMax for the first time, the equipment must receive a full 

battery charge. In order to do this, the equipment needs to be connected to an 

electric current for at least four and a half hours.

Occasional use:

Even when disconnected (stand-by), the CardioMax executes internal routines 

checking the status of the equipment. In spite of this procedure entailing a low 

power consumption, the battery charge may be consumed.
Therefore, whenever the device has not been connected to an electric current for 

more than 20 days, it is advisable to execute a full battery charge. If this procedure 

is not performed, there is a risk of draining the battery and consequently being 

unable to use the CardioMax in its portable configuration (not connected to the 

electric current).

Storage

The battery must be removed from the equipment in case it is stored or not used.

Replacement:

Every battery has a determined lifetime, which is the possible quantity of full charge 

and discharge cycles, without loss of performance (check out the specifications of 

the battery on page 171). When the appliance has a drop in performance of the 

battery, with low autonomy, request a new unit from Instramed technical assistance.
The battery can be replaced following the procedures described on the chapter 

“Care and maintenance”.

Battery replacement is recommended every 02 (two) years or when the runtime is less 

than 01 (one) hour.

III

Battery use

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands