manualshive.com logo in svg

Instramed CardioMax, User Manual

Share
Download
Instramed CardioMax User Manual Download Page 90

User manual | 

AED mode

90

Step 4 - Deliver shock

If the need for shock is detected, the shock symbol will blink and the device will ask 

the user to press the shock button again.

Press “SHOCK” button again.

The shock will be delivered.

ATTENTION: the user must not touch the patient or conductive surfaces 

in contact with him/her during shock delivery, under risk of suffering a 

powerful electric discharge.
NOTE: The energy delivered is pre-adjusted. The user cannot alter this 

protocol. For adult electrodes: 1st shock is 150 J and the following are 

200 J; for child electrodes, all shocks are 50 J.

If clinical scans show that defibrillation is not recommended, the CardioMax will 

announce: “TREATMENT NOT RECOMMENDED”.
Check if there was no movement of the patient during the analysis. If so, restart 

the process. If not, remove pads and start the CPR (cardiopulmonary resuscitation) 

procedure. Details on the next section. 

Press shock 

button!

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands