manualshive.com logo in svg

Instramed CardioMax, User Manual

Share
Download
Instramed CardioMax User Manual Download Page 109

User manual | 

ST segment

109

ST segment configuration

Using the e-Jog, in the main menu, select the ECG parameter and in its submenu, 

the "ST Segment" function to turn on or off this analysis function.

See figure bellow:

WAVEFORM

ECG Response

         Slow

   Fast

[Normal

             

]

ECG Cable                    

         3-wire

   10-wire

[5-wire

                       

]

Detect Pacemaker

                   

           Off

   On

[Off

                                              

]

Segmento ST

                   

           Off

   On

[Off

                                              

]

Sensitivity                    

                 5

   40

[20

                                                   

]

Frequency bandwith

                   

           Diag

   Monitor

[Monitor  ]

Mains supply filter

                   

           Off

   On

[On

                                              

]

40

160

ECG

ECG SETUP

back

exit

-4.4

10.0

ST

1

2

1 - ST segment

Location of the power switch for displaying the "ST Segment" on the main screen of 

CardioMax.

2 - Alarm

Bell icon - Indicates sound alarm off or on. Minimum and maximum alarm limits 

configuration both in the ECG menu and in the alarm menu

.

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands