manualshive.com logo in svg

Instramed CardioMax, User Manual

Share
Download
Instramed CardioMax User Manual Download Page 60

User manual | 

Alarms and limits

60

Defibrillator

ALARM

PRIORITY

COLOR

POSSIBLE CAUSE

Connect pads 

MEDIUM PRIORITY

YELLOW

Pads are not connected.

Ready load

HIGH PRIORITY

RED

It indicates that the load is complete and ready to 

be delivered. 

Defibrillator 

failure 

HIGH PRIORITY

RED

Defibrillator module failure.

INFORMATIVE MESSAGES

Adhesive pads - 

CardioMax detected Adhesive pads connected.

Adult pads - 

CardioMax detected Adult pads connected.

Children pads - 

CardioMax detected paddles connected, but the adult electrode is disconnected. The same 

message is also exhibited when CardioMax detects Children Adhesive pads.

Charging – 

The load is not yet complete.

Shock delivered - 

The energy was delivered to the patient.

Shock disarmed – 

The energy was canceled by the operator.

Shock disarmed (Automatic internal discharge) -

 The energy was automatically canceled because the shock 

button was not pressed before the internal discharge time selected by the operator.

Shock disarmed (Contact Bad) – 

The energy was canceled because the impedance of the patient is not 

satisfying the applicable shock conditions.

Bad Contact – 

Patient impedance measurement is not satisfying the applicable shock conditions.

Pacemaker

ALARM

PRIORITY

COLOR

POSSIBLE CAUSE

Connect 

adhesive pads

MEDIUM PRIORITY

YELLOW

Adhesive paddles are disconnected.

INFORMATIVE MESSAGES

PM: Pause - 

The outbreak of pacemaker pulses is paused.

PM: On - 

The outbreak of pacemaker pulses is on.

Mode: Asynch – 

The pacemaker is in asynchronous mode.

Mode: Dem – 

The pacemaker is in demand mode.

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands