manualshive.com logo in svg

Instramed CardioMax, User Manual

Share
Download
Instramed CardioMax User Manual Download Page 181

User manual | 

Care and maintenance

181

Testing specifications for cabinet interface immunity to RF wire communications equipment

The Ion PRO was designed to provide Basic Security with RF equipment by the following table:

Testing 

frequency (MHz) Band

a 

(MHz) 

Service

a

Modulation

b

Maximum 

power (W)

Distance (m)

Immunity test 

level (V/m)

385

380-390

TETRA 400

Pulse 

modulation

b

 

18 Hz

1.8

0.3

27

450

430-470

GMRS 460

FRS 460

FM

c

 deviation 

of ± 5 kHz
Sinusoidal 

1 kHz

2

0.3

28

710

704-787

Band LTE 13, 17

Pulse 

modulation

b

 

217 Hz

0.2

0.3

9

745

780

810

800-960

GSM 800/900

TETRA 800

iDEN 920

CDMA 850

Band LTE 5

Pulse 

modulation

b

 

18 Hz

2

0.3

28

870

930

1720

1700-1990

GSM 1800

CDMA 1900

GSM 1900

DECT

Band LTE 1, 3, 4, 25

UMTS

Modulação de 

pulso

b

  

217 Hz

2

0.3

28

1845

1970

2450

2400-2570

Bluetooth

WLAN, 802.11 b/g/n

RFID 2450

Band LTE 7

Pulse 

modulation

b

  

217 Hz

2

0.3

28

5240

5100-5800

WLAN 802.11 a/n

Pulse 

modulation

b

 

217 Hz

0.2

0.3

9

5500

5785

NOTE: If necessary, to reach the IMMUNITY TEST LEVEL, the distance between the transmitting antenna and the EM EQUIPMENT or 

EM SYSTEM may be reduced to 1 m. The test distance of 1 m is allowed by ABNT NBR IEC 61000-4-3.

a

 For some services, only the terminal’s transmission frequencies are included.

b

 The carrier must be modulated using a 50% service cycle square wave signal.

c

 As an alternative to FM modulation, 50% to 18 Hz pulse modulation can be used because, although it does not represent actual 

modulation, this would be the worst case.

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands