manualshive.com logo in svg

Instramed CardioMax, User Manual

Share
Download
Instramed CardioMax User Manual Download Page 125

User manual | 

Monitor mode - Capnography

125

4 - Calibration

The equipment is calibrated using a known gas sample, thus configuring its 

measuring curve.

IMPORTANT: Calibration must be performed when the equipment shows 

a message requiring this procedure during initialization. Calibration must 

be performed by QUALIFIED TECHNICAL PERSONNEL.

5 - EtCO

2

 alarm

The “BELL” icon indicates audio “OFF”, “ON” or “PAUSED”. Alarm limits 

configuration “MINIMUM” and “MAXIMUM”.
Is it possible to adjust the EtCO

2

 minimum alarm to levels between 18 and 96 

mmHg, with a 3 mmHg interval when in “Adult” mode and a 1 mmHg interval when 

in “Neo” mode. It is possible to adjust the EtCO

2

 maximum alarm to levels between 

21 and 99 mmHg, with a 3 mmHg interval when in “Adult” mode and a 1 mmHg 

interval when in “Neo” mode.

6 - Back/Exit

“BACK” to Configuration menu or “EXIT” to monitoring screen.

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands