manualshive.com logo in svg

Instramed CardioMax, User Manual

Share
Download
Instramed CardioMax User Manual Download Page 156

User manual | 

PC connection

156

Definition of events displayed in AED mode:

•  INTERNAL DISCHARGE - Power discharged internally due to pressing the start 

button for an excessive amount of time.

•  TREATMENT PERFORMED - A shock was delivered to the patient.
•  SHOCK INDICATED - Shock indicated due to the patient's ventricular fibrillation 

or ventricular tachycardia pattern.

•  SHOCK NOT INDICATED - Shock not indicated on account of the 

electrocardiogram pattern not requiring a shock.

•  ANALYZING AED - Analyzing heart rhythm.
•  ASYSTOLE - Asystole detected.
•  PADS DISCONNECTED - The pads were disconnected.
•  CHILD PADS - Child pads were connected to the device.
•  ADULT PADS - Adult pads were connected to the device.
•  TURNED ON - The equipment was turned on.
•  CPR - Equipment indicating the CPR procedure.

Settings

Volume and clock adjustments via SoftDEA are only available for Isis, Isis 

PRO and Isis PRO training equipment.  In CardioMax these adjustments 

are made via the device's own settings menu, as described on page 49 in 

the "Screen and operation" chapter.

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands