manualshive.com logo in svg

Instramed CardioMax, User Manual

Share
Download
Instramed CardioMax User Manual Download Page 141

User manual | 

RTC - Real Time Check

141

Automatic test

The automatic test can be programed through the menu 

CONFIGURATION > GENERAL CONFIGURATIONS > RTC. To perform the 

automatic test, the equipment should be turned off at the programmed time.
At the configured time, the CardioMax will automatically turn on and begin the test, 

composed of the following steps:
•  Test of the connection with the ECG board.
•  Test of the defibrillator module.
•  Check of the battery level. 
•  Check of the connection with the power outlet.

□

□

□

WARNING

RTC AUTO TEST

PRESS E-JOG TO CANCEL

Communication with the ECG

Defibrillation - 30J

Battery level

Connected to the main power

It is possible to interrupt the test with a click on the e-Jog button.

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands