manualshive.com logo in svg

Instramed CardioMax, User Manual

Share
Download
Instramed CardioMax User Manual Download Page 66

User manual | 

Alarms and limits

66

Minimum/maximum limit

The adjustment of minimum and maximum values is done individually on each 

parameter by using the e-Jog Control. The operator must first select the limit and 

the parameter to be modified and then press it. Next, the desired value must be 

adjusted and then pressed again.

ECG: It is possible to adjust the minimum ECG alarm to levels between 30 and 

100 BPMs with intervals of 5 BPMs in “adult” mode and intervals of 1 BPMs 

in “neo” mode. It is possible to adjust the maximum ECG alarm to levels 

between 100 and 250 BPMs with intervals of 5 BPMs in “adult” mode and 

intervals of 1 BPMs in “neo” mode.
SpO

2

: It is possible to adjust the minimum SpO

2

 alarm to levels between 

40 and 99 BPMs with intervals of 5 BPMs in “adult” mode and intervals of 

1 BPMs in “neo” mode. It is possible to adjust the maximum ECG alarm to 

levels between 41 and 100 BPMs with intervals of 5BPMs in “adult” mode and 

intervals of 1 BPMs in “neo” mode.
NIBP: It is possible to adjust the minimum NIBP alarm to levels between 50 

and 290 mmHg to systolic, diastolic and mean pressure with intervals of 5 

mmHg. It is possible to adjust the maximum NIBP alarm to levels between 60 

and 300 mmHg to systolic, diastolic and mean pressure with intervals of 5 

mmHg.
CO

2

: It is possible to adjust the minimum CO

2

 alarm to levels between 18 and 

96 mmHg, with intervals of 3 mmHg in "adult" mode and intervals of 1 mmHg 

in "neo" mode. It is possible to set the maximum CO

2

 alarm to levels between 

21 and 99 mmHg, with intervals of 3 mmHg in "adult" mode and intervals of 1 

mmHg in "neo" mode.
RESP: It is possible to adjust the minimum respiration alarm to levels 

between 3 and 147 rpm, with intervals of 3 rpm in "adult" mode and intervals 

of 1 rpm in "neo" mode. It is possible to set the maximum respiration alarm 

to levels between 6 and 150 rpm, with intervals of 3 rpm in "adult" mode and 

intervals of 1 rpm in "neo" mode.

85

100

Summary of Contents for CardioMax














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands