manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 97

 

 

KINO-ATOM Motherboard 

Page 79

 

5.1 channel audio kit 

 

7.1 channel audio kit 

5.8.1 5.1 Channel Audio Kit Installation 

 NOTE: 

This is an optional item that must be ordered separately. For further 

information please contact the nearest KINO-ATOM distributor, reseller 

or vendor or contact an iEi sales representative directly. Send any 

queries to 

[email protected]

.  

The optional 5.1 channel audio kit connects to the 10-pin audio connector on the 

KINO-ATOM. The audio kit consists of three audio jacks. One audio jack, Mic In, connects 

to a microphone. The remaining two audio jacks, Line-In and Line-Out, connect to two 

speakers. To install the audio kit, please refer to the steps below: 

Step 1: 

Connect the audio kit cable. 

The audio kit is shipped with a cable that 

connects the audio kit to the KINO-ATOM. Connect the cable to the connector 

on the back of the audio kit. Make sure the pins are properly aligned (i.e. pin 1 

connects to pin 1).

 

Step 2: 

Locate the audio connector

. The location of the 10-pin audio connector is 

shown in 

Chapter 3

. 

Step 3: 

Align pin 1

. Align pin 1 on the on-board connector with pin 1 on the audio kit 

cable connector. Pin 1 on the audio kit cable connector is indicated with a white 

dot. See Figure 5-9. 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands