manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 120

 

 

KINO-ATOM Motherboard

Page 102 

 

Enhanced D

EFAULT

 

Configures the on-board ATA/IDE controller to be in 

Enhanced mode. In this mode, IDE channels and 

SATA channels are separated. This mode supports 

up to 6 storage devices. Some legacy OS do not 

support this mode. 

 

Legacy IDE Channels [PATA Pri, SATA Sec] 

 

SATA Only 

 

Only the SATA drives are enabled. 

 

SATA Pri, PATA Sec 

D

EFAULT

 

The IDE drives are enabled on the Primary 

IDE channel. The SATA drives are enabled on 

the Secondary IDE channel. 

 

PATA Only 

 

The IDE drives are enabled on the primary 

and secondary IDE channels. SATA drives 

are disabled. 

 

IDE Master and IDE Slave 

When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the 

status of the auto detected IDE devices. The following IDE devices are detected and are 

shown in the 

IDE Configuration

 menu: 

 

Primary IDE Master 

 

Primary IDE Slave 

 

Secondary IDE Master 

 

Secondary IDE Slave 

The 

IDE Configuration

 menu (

8

BIOS Menu 4

) allows changes to the configurations for the 

IDE devices installed in the system. If an IDE device is detected, and one of the above 

listed four BIOS configuration options are selected, the IDE configuration options shown in 

Section 

8

6.3.2.1

 appear. 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands