manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 56

 

 

KINO-ATOM Motherboard

Page 38 

Connector 

Type 

Label 

DVI / VGA combo connector 

VGA and 

DVI connector 

VIDEO1 

LAN / USB combo connector 

LAN and 

2 x USB 

LAN/USB1 

LAN/USB2 

PS/2 keyboard / mouse connector 

2 x PS/2 

KBMS1 

Serial port connector 

2 x DB-9 male 

COM1 

Table 4-2: Rear Panel Connectors 

4.2 Internal Peripheral Connectors 

Internal peripheral connectors are found on the motherboard and are only accessible 

when the motherboard is outside of the chassis. This section has complete descriptions of 

all the internal, peripheral connectors on the KINO-ATOM. 

4.2.1 ATX Power Connector 

CN Label: 

PWR1 

CN Type: 

20-pin ATX (2x10) 

CN Location: 

See 

Figure 4-2

 

CN Pinouts: 

See 

Table 4-3

 

The ATX connector is connected to an external ATX power supply. Power is provided to 

the system, from the power supply through this connector. 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands