IEI Technology KINO-ATOM User Manual Download Page 123

Page: 123 / 202

KINO-ATOM Motherboard

Page 105

LBA/Large Mode [Auto]

Use the

LBA/Large Mode

option to disable or enable BIOS to auto detects LBA (Logical

Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the

maximum drive capacity is 137 GB.

Disabled

BIOS is prevented from using the LBA mode control on

the specified channel.

Auto D

EFAULT

BIOS auto detects the LBA mode control on the specified

channel.

Block (Multi Sector Transfer) [Auto]

Use the

Block (Multi Sector Transfer)

to disable or enable BIOS to auto detect if the

device supports multi-sector transfers.

Disabled

BIOS is prevented from using Multi-Sector Transfer on the

specified channel. The data to and from the device occurs

one sector at a time.

Auto D

EFAULT

BIOS auto detects Multi-Sector Transfer support on the

drive on the specified channel. If supported the data

transfer to and from the device occurs multiple sectors at

a time.

PIO Mode [Auto]

Use the

PIO Mode

option to select the IDE PIO (Programmable I/O) mode program timing

cycles between the IDE drive and the programmable IDE controller. As the PIO mode

increases, the cycle time decreases.

Auto D

EFAULT

BIOS auto detects the PIO mode. Use this value if the IDE disk

drive support cannot be determined.

PIO mode 0 selected with a maximum transfer rate of 3.3 MB/s

PIO mode 1 selected with a maximum transfer rate of 5.2 MB/s

PIO mode 2 selected with a maximum transfer rate of 8.3 MB/s

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands