IEI Technology KINO-ATOM User Manual Download Page 42

Page: 42 / 202

KINO-ATOM Motherboard

Page 24

crystal. The RTC keeps track of the time and stores system data even when the system is

turned off.

2.5.7 SATA Controller

The integrated SATA controller on the Intel® ICH7M Southbridge supports two SATA

drives with independent DMA operations. Two SATA controllers are connected to two

SATA connectors on the KINO-ATOM. The SATA connectors are shown in Figure 2-15.

Figure 2-15: SATA Connectors

SATA controller specifications are listed below.

Supports two SATA drives

Supports 1.5 Gb/s data transfer speeds

Supports Serial ATA Specification, Revision 1.0a

2.5.8 USB Controller

Up to six high-speed, full-speed or low-speed USB devices are supported by the Intel®

ICH7M on the KINO-ATOM. High-speed USB 2.0, with data transfers of up to 480 MB/s, is

enabled with the Intel® ICH7M integrated Enhanced Host Controller Interface (EHCI)

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands