IEI Technology KINO-ATOM User Manual Download Page 4

Page: 4 / 202

KINO-ATOM Motherboard

Page iv

Manual Conventions

WARNING!

Warnings appear where overlooked details may cause damage to the equipment or result

in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.

The word “warning” is written as “

WARNING

,” both capitalized and bold and is followed by

text. The text is the warning message. A warning message is shown below:

WARNING:

This is an example of a warning message. Failure to adhere to warning

messages may result in permanent damage to the KINO-ATOM or

personal injury to the user. Please take warning messages seriously.

CAUTION!

Cautionary messages should also be heeded to help reduce the chance of losing data or

damaging the KINO-ATOM. Cautions are easy to recognize. The word “caution” is written

as “

CAUTION

,” both capitalized and bold and is followed. The text is the cautionary

message. A caution message is shown below:

CAUTION:

This is an example of a caution message. Failure to adhere to cautions

messages may result in permanent damage to the KINO-ATOM.

Please take caution messages seriously.

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands