manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 47

 

 

KINO-ATOM Motherboard 

Page 29

 

CPU temperature 

 

System temperature 

The KINO-ATOM Super I/O Enhanced Hardware Monitor also monitors the following fan 

speeds:  

 

CPU Fan speed 

Voltage inputs on the KINO-ATOM Super I/O Enhanced Hardware Monitor monitors the 

following voltages: 

 

CPU Core 

 

+1.05 V 

 

+3.30 V 

 

+5.00 V 

 

+12 V 

 

+1.5 V 

 

+1.8 V 

 

+5 VSB 

 

VBAT 

The values for the above environmental parameters are all recorded in the BIOS 

Hardware Health Configuration menu. 

2.7.2 Operating Temperature and Temperature Control 

The maximum and minimum operating temperatures for the KINO-ATOM are listed below. 

 

Minimum Operating Temperature: 0ºC (32°F) 

 

Maximum Operating Temperature: 60°C (140°F) 

A cooling fan and heat sink must be installed on the CPU. Thermal paste must be 

smeared on the lower side of the heat sink before it is mounted on the CPU. Heat sinks 

are also mounted on the Northbridge and Southbridge chipsets to ensure the operating 

temperature of these chips remain low. 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands