IEI Technology KINO-ATOM User Manual Download Page 44

Page: 44 / 202

KINO-ATOM Motherboard

Page 26

Figure 2-17: LPC Bus

2.6.1 BIOS Chipset

The BIOS chipset has a licensed copy of AMI BIOS installed on the chipset. Some of the

BIOS features are listed below:

AMI Flash BIOS

SMIBIOS (DMI) compliant

Console redirection function support

PXE (Pre-boot Execution Environment) support

USB booting support

2.6.2 iTE IT8718F Super I/O chipset

The iTE IT8718F Super I/O chipset is connected to the Intel® ICH7M Southbridge through

the LPC bus. The iTE IT8718F is an LPC interface-based Super I/O device that comes

with Environment Controller integration. Some of the features of the iTE IT8718F chipset

are listed below:

ACPI and LANDesk Compliant

Enhanced Hardware Monitor

Fan Speed Controller

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands