IEI Technology KINO-ATOM User Manual Download Page 147

Page: 147 / 202

KINO-ATOM Motherboard

Page 129

Enabled

OEM Logo displayed instead of POST messages

AddOn ROM Display Mode [Force BIOS]

The

AddOn ROM Display Mode

option allows add-on ROM (read-only memory)

messages to be displayed.

Force BIOS

EFAULT

Allows the computer system to force a third party

BIOS to display during system boot.

Keep Current

Allows the computer system to display the

information during system boot.

Bootup Num-Lock [Off]

The

Bootup Num-Lock

BIOS option allows the Number Lock setting to be modified

during boot up.

Off D

EFAULT

Does not enable the keyboard Number Lock automatically. To

use the 10-keys on the keyboard, press the Number Lock key

located on the upper left-hand corner of the 10-key pad. The

Number Lock LED on the keyboard lights up when the Number

Lock is engaged.

Allows the Number Lock on the keyboard to be enabled

automatically when the computer system boots up. This allows

the immediate use of the 10-key numeric keypad located on

the right side of the keyboard. To confirm this, the Number

Lock LED light on the keyboard is lit.

Boot From LAN Support [Disabled]

The

BOOT From LAN Support

option enables the system to be booted from a remote

system.

Disabled D

EFAULT

Cannot be booted from a remote system through the

LAN

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands