manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 30

 

 

KINO-ATOM Motherboard

Page 12 

 

Intel® Streaming SIMD Extensions-2 and -3 (Intel® SSE2 and Intel® SSE3) 

support and Supplemental Streaming SIMD Extension 3 (SSSE3) support 

 

Micro-FCBGA8 packaging technologies 

 

Thermal management support via Intel® Thermal Monitor 1 and Intel Thermal 

Monitor 2 

 

FSB Lane Reversal for flexible routing 

 

Supports C0/C1(e)/C2(e)/C4(e) 

 

L2 Dynamic Cache Sizing 

 

Advanced power management features including Enhanced Intel 

SpeedStep® Technology 

 

Execute Disable Bit support for enhanced security 

2.3.3 Front Side Bus (FSB) 

The Intel® Atom™ processor on the KINO-ATOM is interfaced to the Intel® 945GSE 

Northbridge through a 533 MHz front side bus (FSB). The FSB is shown in 

7

Figure 2-5

 

below. 

 

Figure 2-5: Front Side Bus 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands