manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 108

 

 

KINO-ATOM Motherboard

Page 90 

Step 1: 

Locate the dual PS/2 connector

. The location of the PS/2 connector is shown 

in 

Chapter 3

. 

Step 2: 

Insert the keyboard/mouse connector

.

 

Insert the PS/2 connector on the end 

of the PS/2 y-cable into the external PS/2 connector. See 

Figure 5-19

. 

 

Figure 5-19: PS/2 Keyboard/Mouse Connector 

Step 3: 

Connect the keyboard and mouse

. Connect the keyboard and mouse to the 

appropriate connector. The keyboard and mouse connectors can be 

distinguished from each other by looking at the small graphic at the top of the 

connector.

 

Step 0:

 

5.9.3 Serial Device Connection 

The KINO-ATOM has a single female DB-9 connector on the external peripheral interface 

panel for a serial device. Follow the steps below to connect a serial device to the 

KINO-ATOM. 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands