manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 101

 

 

KINO-ATOM Motherboard 

Page 83

Step 3: 

Connect the cable to an IDE device

. Connect the two connectors on the other 

side of the cable to one or two IDE devices. Make sure that pin 1 on the cable 

corresponds to pin 1 on the connector.

 

Step 0:

 

5.8.4 SATA Drive Connection 

The KINO-ATOM is shipped with two SATA drive cables and one SATA drive power cable. 

To connect the SATA drives to the connectors, please follow the steps below. 

Step 1: 

Locate the connectors

. The locations of the SATA drive connectors are shown 

in 

Chapter 3

. 

Step 2: 

Insert the cable connector

. Press the clip on the connector at the end of the 

SATA cable and insert the cable connector into the onboard SATA drive 

connector. See 

8

Figure 5-12

. 

 

Figure 5-12: SATA Drive Cable Connection 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands