IEI Technology KINO-ATOM User Manual Download Page 122

Page: 122 / 202

KINO-ATOM Motherboard

Page 104

Block Mode

: Block mode boosts IDE drive performance by increasing the

amount of data transferred. Only 512 bytes of data can be transferred per

interrupt if block mode is not used. Block mode allows transfers of up to 64 KB

per interrupt.

PIO Mode

: Indicates the PIO mode of the installed device.

Async DMA

: Indicates the highest Asynchronous DMA Mode that is

supported.

Ultra DMA

: Indicates the highest Synchronous DMA Mode that is supported.

S.M.A.R.T.

: Indicates whether or not the Self-Monitoring Analysis and

Reporting Technology protocol is supported.

32Bit Data Transfer

: Enables 32-bit data transfer.

Type [Auto]

Use the

Type

BIOS option select the type of device the AMIBIOS attempts to boot from

after the Power-On Self-Test (POST) is complete.

Not Installed

BIOS is prevented from searching for an IDE disk

drive on the specified channel.

Auto D

EFAULT

The BIOS auto detects the IDE disk drive type

attached to the specified channel. This setting should

be used if an IDE hard disk drive is attached to the

specified channel.

CD/DVD

The CD/DVD option specifies that an IDE CD-ROM

drive is attached to the specified IDE channel. The

BIOS does not attempt to search for other types of

IDE disk drives on the specified channel.

ARMD

This option specifies an ATAPI Removable Media

Device. These include, but are not limited to:

ZIP

LS-120

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands