IEI Technology KINO-ATOM User Manual Download Page 110

Page: 110 / 202

KINO-ATOM Motherboard

Page 92

Step 2:

Insert a USB Series "A" plug

. Insert the USB Series "A" plug of a device into

the USB Series "A" receptacle on the external peripheral interface. See

Figure 5-21

Step 0:

Figure 5-21: USB Connector

5.9.5 VGA Monitor Connection

The KINO-ATOM has a single female DB-15 connector on the external peripheral

interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect

a monitor to the KINO-ATOM, please follow the instructions below.

Step 1:

Locate the female DB-15 connector

. The location of the female DB-15

connector is shown in

Chapter 3

Step 2:

Align the VGA connector

. Align the male DB-15 connector on the VGA screen

cable with the female DB-15 connector on the external peripheral interface.

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands