IEI Technology KINO-ATOM User Manual Download Page 152

Page: 152 / 202

KINO-ATOM Motherboard

Page 134

Internal Graphics Mode Select [Enable, 8 MB]

The

Internal Graphic Mode Select

option determines the amount of system memory that

can be used by the Internal graphics device.

Disable

Enable, 1 MB

1 MB of memory used by internal graphics device

Enable, 8 MB

EFAULT

8 MB of memory used by internal graphics device

DVMT Mode Select [DVMT Mode]

Use the

DVMT Mode Select

option to select the Intel

Dynamic Video Memory Technology

(DVMT) operating mode.

Fixed Mode

A fixed portion of graphics memory is reserved as

graphics memory.

DVMT Mode

EFAULT

Graphics memory is dynamically allocated

according to the system and graphics needs.

Combo Mode

A fixed portion of graphics memory is reserved as

graphics memory. If more memory is needed,

graphics memory is dynamically allocated

according to the system and graphics needs.

DVMT/FIXED Memory

Use the

DVMT/FIXED Memory

option to specify the maximum amount of memory that

can be allocated as graphics memory. This option can only be configured for if

DVMT

Mode

Fixed Mode

is selected in the

DVMT Mode Selec

t option. If

Combo Mode

selected, the maximum amount of graphics memory is 128 MB. Configuration options are

listed below.

64 MB

128 MB

EFAULT

Maximum DVMT

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands