IEI Technology KINO-ATOM User Manual Download Page 68

Page: 68 / 202

KINO-ATOM Motherboard

Page 50

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1 GROUND

2 GROUND

3 L 4 LVDSA_Y0-

5 L 6 LVDSA_Y1-

7 L 8 LVDSA_Y2-

9 LV

10 LVDSA_CLK-

11 N/C

12 N/C

13 GROUND

14 GROUND

15 L 16 LVDSB_Y0-

17 L 18 LVDSB_Y1-

19 L 20 LVDSB_Y2-

21 LV 22 LVDSB_CLK-

23 N/C

24 N/C

25 GROUND

26 GROUND

27 VCC_LVDS 28 VCC_LVDS

29 VCC_LVDS 30 VCC_LVDS

Table 4-12: LVDS LCD Port Connector Pinouts

4.2.11 PCIe Mini Card Slot

CN Label:

MINI_PCIE1

CN Type:

52-pin Mini PCIe Card Slot

CN Location:

The PCIe mini card slot enables a PCIe mini card expansion module to be connected to

the board. Cards supported include among others wireless LAN (WLAN) cards.

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands