IEI Technology KINO-ATOM User Manual Download Page 76

Page: 76 / 202

KINO-ATOM Motherboard

Page 58

1 x VGA connector

Figure 4-18: KINO-ATOM External Peripheral Interface Connector

4.3.1 Audio Connector

CN Label:

AUDIO1

CN Type:

2 x audio jacks

CN Location:

See

Figure 4-18

The three audio jacks on the external audio connector enable the KINO-ATOM to be

connected to external audio devices as specified below.

Line Out port (Lime):

Connects to a headphone or a speaker. With

multi-channel configurations, this port can also connect to front speakers.

Microphone (Pink):

Connects a microphone.

Figure 4-19: Audio Connector

4.3.2 Keyboard/Mouse Connector

CN Label:

KBMS1

CN Type:

Dual PS/2

CN Location:

See

Figure 4-18

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands