IEI Technology KINO-ATOM User Manual Download Page 75

Page: 75 / 202

KINO-ATOM Motherboard

Page 57

The 2x4 USB pin connector provides connectivity to two USB 1.1 or two USB 2.0 ports.

The USB connector can support two USB devices. Additional external USB ports are

found on the rear panel. The USB ports are used for I/O bus expansion.

Figure 4-17: USB Connector Pinout Locations

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

USB Connector 1

USB Connector 2

1 VCC

2 GND

3 DATA1- 4 DATA2+

5 DATA1+ 6 DATA2-

7 GND

8 VCC

Table 4-18: USB Port Connector Pinouts

4.3 External Peripheral Interface Connector Panel

Figure 4-18

shows the KINO-ATOM external peripheral interface connector (EPIC) panel.

The KINO-ATOM EPIC panel consists of the following:

2 x Audio jacks

1 x DVI connector

2 x RJ-45 LAN connectors

2 x PS/2 connectors

2 x Serial port connectors

4 x USB connectors

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands