IEI Technology KINO-ATOM User Manual Download Page 140

Page: 140 / 202

KINO-ATOM Motherboard

Page 122

VT-UTF8 Combo Key Support [Disabled]

Use the

VT-UFT8 Combo Key Support

option to enable additional keys that are not

provided by VT100 for the PC 101 keyboard.

The VT100 Terminal Definition is the standard convention used to configure and conduct

emergency management tasks with UNIX-based servers. VT100 does not support all keys

on the standard PC 101-key layout, however. The VT-UTF8 convention makes available

additional keys that are not provided by VT100 for the PC 101 keyboard.

Disabled D

EFAULT

Disables the VT-UTF8 terminal keys

Enabled

Enables the VT-UTF8 combination key. Support for

ANSI/VT100 terminals

Sredir Memory Display Delay [Disabled]

Use the

Sredir Memory Display Delay

option to select the delay before memory

information is displayed. Configuration options are listed below

No Delay

EFAULT

Delay 1 sec

Delay 2 sec

Delay 4 sec

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands