manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 100

 

 

KINO-ATOM Motherboard

Page 82 

Step 5: 

Connect the audio devices

. Connect one speaker to the line-in audio jack, one 

speaker to the line-out audio jack and a microphone to the mic-in audio jack. 

Step 6: 

Install the driver

. If the 7.1 channel audio kit is used, the ALC883 Realtek 

codec driver must be installed. Refer to 

Chapter 7

 for driver installation 

instructions.

Step 0:

 

5.8.3 ATA Flat Cable Connection 

The ATA 66/100 flat cable connects to the KINO-ATOM to one or two IDE devices. To 

connect an IDE HDD to the KINO-ATOM please follow the instructions below. 

Step 1: 

Locate the IDE connector

. The location/s of the IDE device connector/s is/are 

shown in 

Chapter 3

. 

Step 2: 

Insert the connector

. Connect the IDE cable connector to the onboard 

connector. See 

8

Figure 5-11

. A key on the front of the cable connector ensures it 

can only be inserted in one direction. 

 

Figure 5-11: IDE Cable Connection 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands