manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 33

 

 

KINO-ATOM Motherboard 

Page 15

 

Figure 2-8: Graphics 

2.4.2.1 Analog CRT (VGA) 

A DB-15 VGA connector on the external peripheral interface connector panel is interfaced 

to the Intel® 945GSE graphics engine. The Intel® 945GSE internal graphics engine, with 

an integrated 400 MHz RAMDAC and hot plug CRT support, supports analog CRT 

monitors up to QXGA. 

2.4.2.2 LVDS 

A 30-pin LVDS crimp connector is interfaced to the Intel® 945GSE graphics engine. The 

Intel® 945GSE internal graphics engine supports LVDS displays with the following 

features: 

 

Up to UXGA monitors with a maximum resolution of 1600 x 1200 

 

18-bit 25 MHz to 112 MHz single-channel or dual-channel LVDS screens 

 

CPIS 1.5 compliant LVDS screens 

2.4.2.3 TV Out 

An external 7-pin DIN TV output connector is interfaced to the Intel® 945GSE graphics 

engine. The Intel® 945GSE internal graphics engine has the following TV output features: 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands