manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 37

 

 

KINO-ATOM Motherboard 

Page 19

PIO IDE transfers up to 16 MB/s and Ultra ATA transfers of 100 MB/s. The integrated IDE 

interface is able to support the following IDE HDDs: 

 

Ultra ATA/100

, with data transfer rates up to 100 MB/s 

 

Ultra ATA/66

, with data transfer rates up to 66 MB/s 

 

Ultra ATA/33

, with data transfer rates up to 33 MB/s 

Specification 

Ultra ATA/100 

Ultra ATA/66 

Ultra ATA/33 

IDE devices 

2 2 

2 

PIO Mode 

0 – 4 

0 – 4 

0 – 4 

PIO Max Transfer Rate 

16.6 MB/s 

16.6 MB/s 

16.6 MB/s 

DMA/UDMA designation 

UDMA 5 

UDMA 4 

UDMA 2 

DMA/UDMA Max Transfer 

100 MB/s 

66 MB/s 

33 MB/s 

Controller Interface 

5 V 

5 V 

5 V 

Table 2-1: Supported HDD Specifications 

2.5.2.2 CompactFlash® Slot 

The CompactFlash® slot on the KINO-ATOM is interfaced through the IDE interface on 

the Intel® ICH7M Southbridge. The CompactFlash® slot is shown in 

Figure 2-10

 below. 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands