IEI Technology KINO-ATOM User Manual Download Page 144

Page: 144 / 202

KINO-ATOM Motherboard

Page 126

IRQ10

IRQ 11

IRQ 14

IRQ 15

DMA Channel# [Available]

Use the

DMA Channel#

option to assign a specific DMA channel to a particular PCI/PnP

device.

Available D

EFAULT

The specified DMA is available to be used by

PCI/PnP devices

Reserved

The specified DMA is reserved for use by Legacy

ISA devices

Available DMA Channels are:

DM Channel 0

DM Channel 1

DM Channel 3

DM Channel 5

DM Channel 6

DM Channel 7

Reserved Memory Size [Disabled]

Use the

Reserved Memory Size

BIOS option to specify the amount of memory that

should be reserved for legacy ISA devices.

Disabled D

EFAULT

No memory block reserved for legacy ISA devices

16K

16 KB reserved for legacy ISA devices

32K

32 KB reserved for legacy ISA devices

64K

54 KB reserved for legacy ISA devices

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands