manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 84

 

 

KINO-ATOM Motherboard

Page 66 

5.2 Installation Considerations 

 NOTE: 

The following installation notices and installation considerations should 

be read and understood before the KINO-ATOM is installed. All 

installation notices pertaining to the installation of the KINO-ATOM 

should be strictly adhered to. Failing to adhere to these precautions 

may lead to severe damage of the KINO-ATOM and injury to the 

person installing the motherboard. 

5.2.1 Installation Notices 

 WARNING: 

The installation instructions described in this manual should be 

carefully followed in order to prevent damage to the KINO-ATOM, 

KINO-ATOM components and injury to the user. 

Before and during the installation please 

DO

 the following: 

 

Read the user manual: 

o 

The user manual provides a complete description of the KINO-ATOM 

installation instructions and configuration options. 

 

Wear an electrostatic discharge cuff (ESD): 

o 

Electronic components are easily damaged by ESD. Wearing an ESD cuff 

removes ESD from the body and helps prevent ESD damage. 

 

Place the KINO-ATOM on an antistatic pad: 

o 

When installing or configuring the motherboard, place it on an antistatic 

pad. This helps to prevent potential ESD damage. 

 

Turn all power to the KINO-ATOM off: 

o 

When working with the KINO-ATOM, make sure that it is disconnected 

from all power supplies and that no electricity is being fed into the system. 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands