IEI Technology KINO-ATOM User Manual Download Page 142

Page: 142 / 202

KINO-ATOM Motherboard

Page 124

Enabled D

EFAULT

USB function enabled

USB2.0 Controller Mode [HiSpeed]

The

USB2.0 Controller Mode

BIOS option sets the speed of the USB2.0 controller.

FullSpeed

The controller is capable of operating at full speed

12 Mb/s

HiSpeed D

EFAULT

The controller is capable of operating at high speed

480 Mb/s

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded onto the system.

Disabled

Legacy USB support disabled

Enabled D

EFAULT

Legacy USB support enabled

Auto

Legacy USB support disabled if no USB devices are

connected

6.4 PCI/PnP

Use the PCI/PnP menu (

BIOS Menu 12

) to configure advanced PCI and PnP settings.

WARNING:

Setting wrong values for the BIOS selections in the PCIPnP BIOS

menu may cause the system to malfunction.

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands