IEI Technology KINO-ATOM User Manual Download Page 34

Page: 34 / 202

KINO-ATOM Motherboard

Page 16

Three integrated 10-bit DACs

Macrovision support

Overscaling

NTSC and PAL formats supported

Supports RCA or S-VIDEO connectivity

Supports HDTV with the following resolutions:

480p

720p

1080i

1080p

2.4.2.4 SDVO and DVI

The SDVO is connected to the DVI output through the Silicon Image Sil1362. The Intel®

945GSE internal graphics engine has the following SDVO output features:

Concurrent operation of PCIe x 1 with SDVO

Two SDVO ports supported

SDVO is muxed onto the PCIe pins

DVI 1.0 support for external digital monitor

Only Downstream HDCP support

Supports TV and DVD formats

Display hot plug support

2.5 Intel® ICH7M Southbridge Chipset

The Intel® ICH7M Southbridge chipset is connected to the Intel® 945GSE Northbridge

GMCH through the chip-to-chip Direct Media Interface (DMI). Some of the features of the

Intel® ICH7M are listed below.

Summary of Contents for KINO-ATOM











































































































































































































Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands

IEI Technology KINO-ATOM, User Manual

Search results

Summary of Contents for KINO-ATOM

Reviews:

Brands by name

Popular brands