IBM 3745 Series, Hardware Maintenance Reference

Page: 576 / 712

CA BER
NCP CA BER Type 10
CA BER Type 10 - Summary
Table 11-58 (Page 1 of 5). CA BER Type 10 Summary
BER
ID Abend
Code
(NCP) Event Description Recovery
or PGM
Action ALERT ALARM
10 0915 Ÿ CADS: Invalid ESC address used (EP or NEO are
the CA owner)
– Mismatch between ESC addresses range
defined in NCP/PEP sysgen and in MOSS CDF
for involved CA.
– Program error (for example, possible overwrite
of control blocks where ESC values are kept) if
found in normal operations
Ÿ BCCA: ESC addresses not allowed on this type of
CA.
NCP re-IPL NO NO
14 0910 Address exception (AIO) (X'76' bit 0.0 or 1.0 ON) NCP re-IPL NO NO
16 0911 Storage protect (AIO) (X'76' bit 0.1 or 1.1 ON) NCP re-IPL NO NO
18 0912 Invalid CA selection in control program (attempt to
select a non-installed CA). Control program issuing an
output X'07' with either bit 0.2 or 0.3 set and bits 0.4,
0.6 indicating select bits for a CA that is not installed. NCP re-IPL NO NO
1B 0913 Invalid IOH/IOHI input to CA (for example input to reg-
ister which cannot be read) X'7E' bit 0.5 ON NCP re-IPL NO NO
1C 0914 Output sequence issued in error to CA X'0D' bit 1.0 ON NCP re-IPL NO NO
1E 0913 Invalid IOH/IOHI output to CA output X'0D', X'0E', or
X'0F' NCP re-IPL NO NO
1F 0913 Invalid IOH/IOHI output to CA (hardware detected)
X'7E' bit 0.5 ON NCP re-IPL NO NO
34 091F Level 3 IPL configuration check
Ÿ Stacked status cleared by initial select for the 1st
time, or transfer of final status but not on the
IPLing CA. built for the non-IPLing CA
Ÿ PRI built for the IPLing CA
NCP re-IPL NO NO
35 0 ESC address (from host) not within range (PEP on
level 3 interrupt)
Mismatch between ESC addresses range defined in
NCP/PEP sysgen and in MOSS CDF for involved CA. NO NO
80 0 Autoselection error: IOH IN X'0F' failed (X'09' and X'0A'
contain 'FEFE') Retry cmd
in X'0F'
80 0920 Autoselection error (limit threshold)
Ÿ
X'76' bit 0.4 ON for IOC1 time out, or
Ÿ X'76' bits 0.0 to 0.3 contain '0010'.
NCP re-IPL NO NO
80 0 Autoselection error (limit threshold)
Ÿ
X'76' bit 0.4 ON for IOC1 time out, or
Ÿ
X'76' bits 0.0 to 0.3 contain '0101'.
CA down 50 50
80 0920 Autoselection error (limit threshold)
Ÿ
X'76' bit 0.4 ON for IOC1 time out, or
Ÿ
X'76' bits 0.0 to 0.3 contain '0101'.
NCP re-IPL NO NO
11-164
IBM 3745 Models 130, 150, 160, 170, and 17A: Hardware Maintenance Reference