Humminbird MEGA Live Manual Download | Manualshive

Page: 27 / 75

background image

21

MEGA Live Installation

Connecting the Heading Collar and Mount

Align the cables so that

the TargetLock heading

sensor cable is on top

of the MEGA Live power

and ethernet cables.

Secure the heading
collar and mount before
securing the TargetLock
heading sensor to the
mount.

6. Slide the provided sleeving over all three cables, pushing one end into the

opening of the mount.

7. Adjust the sleeving until it is smooth and then secure both ends using one of

the included cable tie just outside of the TargetLock heading sensor mount and
a second cable tie around the body of the transducer ethernet connector.

8. Fold excess sleeving back on itself and secure it with cable ties.

NOTE:

If you do not plan to remove your unit frequently, you may also use the

excess sleeving to cover all of the connectors.

«
...
25
26
27
28
29
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: DANLERS Pages: 2

Brand: Haas Automation Pages: 26

Brand: MAHA Pages: 21

Brand: MAGUIRE Pages: 47

Brand: olympia electronics Pages: 4

Brand: Ultimate Healthcare Pages: 2

Brand: Ultimate Healthcare Pages: 40

Brand: Yamaha Pages: 139

Brand: Yamaha Pages: 19

Brand: Yamaha Pages: 32

Brand: Vaillant Pages: 76

Brand: H2flow Pages: 2

Brand: V-TAC Pages: 27

Brand: Yacht Sentinel Pages: 32

Brand: X-FLOC Pages: 35

Brand: Feniex Pages: 5

SimNewB Anomaly Set

Brand: laerdal Pages: 10

Brand: Otto Bock Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands