Humminbird MEGA Live Manual Download

Page: 66 / 75

Power Off

Power Off

WARNING!

When the boat is stored or at dock, the MEGA Live Imaging transducer

must be turned off to prevent draining the battery.

Power Off the Control Head

APEX/SOLIX Series:

During operation, tap the top, right corner of the status

bar or press the POWER key, and select Power Off.

HELIX Series:

Press and hold the POWER key.

CAUTION!

Turning off the control head will NOT power off the MEGA Live

Imaging transducer.

2. Turn off power on the main switch, breaker, or battery switch.

Powering off the MEGA Live Imaging transducer will be determined by the
installation and power connection on your boat.

Travel with the MEGA Live Transducer Installed

The MEGA Live transducer must not hit the deck, base, or any objects. This is critical
during transport. Check the tension of the trolling motor bracket after initial use and
periodically thereafter to ensure that the installation remains stable.

Summary of Contents for MEGA Live












































































Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands

Humminbird MEGA Live, Manual

Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands