Humminbird MEGA Live Manual Download Page 58 | Manualshive

Page: 58 / 75

background image

52

Control Head Setup

4. Pair the TargetLock Heading Sensor to the Control Head

Use the following instructions to pair the MEGA Live Imaging TargetLock Heading
Sensor to your Humminbird control head.

APEX/SOLIX Series

1. Press the HOME key.

2. Select Settings > CHIRP Sonar > Pair TargetLock Heading Sensor.

3. On your TargetLock Heading Sensor, press the Pair button.

4. The control head and the TargetLock Heading Sensor will go into Pairing Mode.

If 30 seconds pass while in Pairing Mode and they do not successfully pair, an
error message will display signaling that the pairing has timed out. Repeat the
procedure.

NOTE:

You can check the MEGA Live Device List to confirm that the TargetLock

Heading Sensor is paired. Select Home > Settings > CHIRP Sonar > Device List.

HELIX Series

1.

Main Menu:

On your control head, press the MENU key twice.

2. Select the Accessories tab > MEGA Live > MEGA Live Installation.

3. Select Pair TL Heading Sensor, and press the RIGHT Cursor key.

4. On your TargetLock Heading Sensor, press the Pair button.

5. The control head and the TargetLock Heading Sensor will go into Pairing Mode.

If 30 seconds pass while in Pairing Mode and they do not successfully pair, an
error message will display signaling that the pairing has timed out. Repeat the
procedure.

NOTE:

You can check the MEGA Live Device List to confirm that the TargetLock

Heading Sensor is paired. Press the MENU key twice to open the Main Menu.
Select the Accessories tab > MEGA Live > Device List.

«
...
56
57
58
59
60
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: Camozzi Pages: 2

Brand: Oktober Pages: 22

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Brand: UNIA Pages: 62

Brand: R2 Pages: 20

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: vanEE Pages: 52

Brand: Caddon Hives Pages: 3

Brand: Halyard Pages: 88

Brand: HALDER Pages: 2

Brand: Hällde Pages: 40

Brand: Hällde Pages: 6

Brand: Guyatone Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands