Humminbird MEGA Live Manual Download Page 30 | Manualshive

Page: 30 / 75

background image

24

MEGA Live Foot Pedal Installation

Install the MEGA Live Imaging TargetLock Foot Pedal

Before mounting your MEGA Live Imaging TargetLock foot pedal, please give
consideration to the following:

• Examine your boat to ensure that you will not drill into any obstructions and

that the hardware will be accessible for assembly.

• Make sure the area under the mounting location is flat, clear to drill holes and

that the installation hardware will not damage existing components below
the mounting surface. It may be necessary to shim or modify the mounting
surface under the mounting location to create a flat area for the foot pedal
to be mounted.

• Mount the foot pedal in an area that has a clear line of communication with

your Humminbird.

• Mount the foot pedal in an area where it will not become a tripping hazard.

1. Once you have selected a mounting location for your foot pedal, remove the

foot pedal from the base by squeezing the tabs on both sides of the foot pedal
and pulling the pedal and base apart.

Separating the Foot Pedal and Base

«
...
28
29
30
31
32
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: iGuzzini Pages: 20

Brand: Eagle Pages: 3

Brand: Makita Pages: 10

Brand: SALUDA MEDICAL Pages: 61

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

D-MAS HyperSat 2540

Brand: DanMedical Pages: 103

Brand: Parker Research Corp Pages: 4

Brand: Eastwood Pages: 20

Brand: Daihan Scientific Pages: 43

Sportsound SSR-200

Brand: Daktronics Pages: 5

Brand: IDS Pages: 2

Brand: Quark-Elec Pages: 2

Brand: Xtool Pages: 8

Brand: Valko Pages: 10

Brand: LSI Pages: 24

VIMCO Sivoia SV-CCI-GRP

Brand: Lutron Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands