Humminbird MEGA Live Manual Download Page 59 | Manualshive

Page: 59 / 75

background image

53

Control Head Setup

5. Pair the Foot Pedal to the Control Head

Use the following instructions to pair the wireless foot pedal to the Humminbird
Control Head.

Foot Pedal

left/pairing

right/pairing

One-Boat Network

TargetLock

LED lights

APEX/SOLIX Series

1. Press the HOME key.

2. Select Settings > CHIRP Sonar > MEGA Live > Pair TargetLock Foot Pedal.

3. On your foot pedal, press and hold the Left button and the Right button at the

same time until the LEDs at the top of the pedal begin to scroll. Then release
the buttons.

4. The control head and the foot pedal will go into Pairing Mode.

If 30 seconds pass while in Pairing Mode and they do not successfully pair, an
error message will display signaling that the pairing has timed out. Repeat the
procedure.

NOTE:

After pairing completes, if the lights on the foot pedal blink in a scrolling

pattern, this indicates that the control head is updating the foot pedal. When the
software update is complete, the pairing process will need to be repeated.

«
...
57
58
59
60
61
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: ABB Pages: 6

Brand: Hanil Pages: 60

Brand: Raymarine Pages: 24

Brand: Hansen Pages: 72

Brand: AAT Pages: 16

Brand: AAT Pages: 40

Platinum Series

Brand: Dairy Tech Pages: 38

Brand: H&S Pages: 34

Brand: QAL Medical Pages: 42

Brand: Bard Pages: 144

Brand: GALBIATI Pages: 8

Brand: Vahva Jussi Pages: 9

Brand: Baoding Longer Precision Pump Pages: 6

Brand: Tascam Pages: 128

Brand: ParaBody Pages: 6

Brand: tayco Pages: 111

Brand: Parkside Pages: 95

Brand: Parker Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands