Humminbird MEGA Live Manual Download

Page: 12 / 75

Update Software

Update Software with FishSmart

You can use the FishSmart App to download and push software updates directly to
your Humminbird control head or accessory.

NOTE:

It is important to install the latest software update on your control head to

enable all FishSmart features. For the latest software update, visit our Web site at

humminbird.com

NOTE:

You must first download the FishSmart App and pair your mobile device to

your control head. See the

FishSmart User Manual

for more information.

1. Open the FishSmart App on your mobile device.

Apple iOS:

Tap the System menu icon.

Google Android:

Tap the FishSmart main menu. Select system.

3. Tap Update next to the selected unit. The download progress is displayed on

the screen.

4. Tap Transfer next to the selected unit once the download is complete.

5. Confirm the estimated transfer time.

6. Tap the checkbox to select where to upload the software update (internal

storage, card slot 1, or card slot 2).

NOTE:

For APEX and SOLIX Series control heads, you cannot download

software updates to an SD or microSD card with LakeMaster charts saved to it.

7. Tap Transfer. The upload progress is displayed on the System menu in FishSmart

and in the System Status view on the control head.

8. Follow the on-screen prompts on the control head to complete the software

installation.

Summary of Contents for MEGA Live












































































Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands

Humminbird MEGA Live, Manual

Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands