Humminbird MEGA Live Manual Download | Manualshive

Page: 39 / 75

background image

33

MEGA 360 Installation

5. Use an Allen wrench (not included) to tighten the hardware just enough to keep

the collar assembled.

6. Slide the collar up to the base of the BowGuard.

7. Use an Allen wrench (not included) to fully tighten the socket bolts until they

are secure.

Hand-tighten only!

Details:

Tighten the socket bolts and collar clamp hardware evenly on both

sides of the clamp until you feel them start to compress and secure, and then
tighten each bolt an additional 1/4 to 1/2 turn.

WARNING!

The socket bolts must be tightened completely to prevent the trolling

motor from potentially damaging the pod.

Hand-tighten only!

«
...
37
38
39
40
41
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: GE Pages: 14

Brand: GE Pages: 11

Brand: GE Pages: 20

Druck ADTS 2 Series

Brand: GE Pages: 18

Litmann Quality 3100

Brand: 3M Pages: 2

Brand: Fisher Scientific Pages: 42

Brand: Warehouse-lighting Pages: 3

Brand: Eagle Group Pages: 8

Brand: E2S Pages: 5

Brand: Fayat Group Pages: 50

Brand: Halyard Pages: 88

Brand: YMC Pages: 49

Brand: Octane Fitness Pages: 8

Brand: Octane Fitness Pages: 10

Brand: OCENCO Pages: 48

Brand: Ocean Optics Pages: 6

Brand: Taylor Pages: 41

Brand: Bartscher Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands