Humminbird MEGA Live Manual Download

Page: 9 / 75

Update Software

Update Software

Your control head model may need a software update to work with the MEGA Live
Imaging transducer. We recommend that you read the following section completely
before starting any software updates.

NOTE:

It is important to install the latest software update on your control head to

enable all MEGA Live Imaging TargetLock features. For the latest software updates,
visit our Web site at

humminbird.com

Check the Current Software Version

It is helpful to review the software version number that is currently installed on the
control head and each accessory.

APEX/SOLIX Series

1. Press the HOME key.

2. Select Settings.

3. Select Network > Network Info.

4. The Network Info dialog box shows a section for each device connected to the

network. Scroll to each section to note the software version number listed.

HELIX Series

1. Press and hold the VIEW key.

2. Select System > System Status.

3. Confirm the Software Version listed.

Summary of Contents for MEGA Live












































































Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands

Humminbird MEGA Live, Manual

Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands