Humminbird MEGA Live Manual Download Page 60 | Manualshive

Page: 60 / 75

background image

54

Control Head Setup

NOTE:

You can check the MEGA Live Device List to confirm that the foot pedal

is paired. Select Home > Settings > CHIRP Sonar > Device List.

HELIX Series

1.

Main Menu:

On your control head, press the MENU key twice.

2. Select the Accessories tab > MEGA Live > MEGA Live Installation.

3. Select Pair TL Foot Pedal, and press the RIGHT Cursor key.

4. On your foot pedal, press and hold the Left button and the Right button at the

same time until the LEDs at the top of the pedal begin to scroll. Then release
the buttons.

5. The control head and the foot pedal will go into Pairing Mode.

If 30 seconds pass while in Pairing Mode and they do not successfully pair, an
error message will display signaling that the pairing has timed out. Repeat the
procedure.

NOTE:

After pairing completes, if the lights on the foot pedal blink in a

scrolling pattern, this indicates that the control head is updating the foot pedal.
When the software update is complete, the pairing process will need to be
repeated.

NOTE:

You can check the MEGA Live Device List to confirm that the foot pedal

is paired. Press the MENU key twice to open the Main Menu. Select the
Accessories tab > MEGA Live > Device List.

«
...
58
59
60
61
62
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: Oemtools Pages: 4

Brand: Keithley Pages: 32

Brand: jcb Pages: 166

LOUDEN 200 Series

Brand: ACCO Brands Pages: 144

Brand: B&K Pages: 16

Brand: B&G Pages: 29

Brand: B&G Pages: 2

Brand: Rangevision Pages: 28

Brand: Farmet Pages: 102

Brand: jcb Pages: 41

IMPULSE 2 IT8026 Glute Master

Brand: BM FITNESS Pages: 18

HomeFill HF2POST6

Brand: Invacare Pages: 24

Brand: WhizRider Pages: 24

A/C Air Launcher 101050

Brand: CITC Pages: 10

Brand: Meyer Pages: 4

Brand: PASCO Pages: 3

Brand: Taurus Pages: 44

MiNiSTUDIO PERSONAL US-32

Brand: Tascam Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands