Humminbird MEGA Live Manual Download Page 21

Page: 21 / 75

MEGA Live Installation

5. Secure the Landscape Mode mount to the transducer with one of the included

lock washers and 1/4-28 screws, using the provided hex bit. Hand tighten until
the lock washer is fully compressed (see the illustration

Compressing the Lock

Washer

), and then tighten an additional 1/4 turn.

Hand tighten only!

WARNING!

The screw and lock washer MUST be fully tightened.

Failure

to do so may result in the transducer detaching from the Landscape Mode
mount in the water.

6. Feed the transducer cables through the shaft until the last molded anchor point

has just passed the shaft mount (see the illustration

Routing the Cables

Routing the Cables

molded
anchor point

shaft

mount

7. Connect the cable cover to the shaft mount. The last molded anchor point is

keyed to fit into the base of the cable cover (see the illustration

Connecting

the Cable Cover

8. Secure the cable cover with the four (4) included 8-32 screws, using the

provided 9/64" Allen wrench.

Hand tighten only!

Summary of Contents for MEGA Live












































































Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands

Humminbird MEGA Live, Manual

Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands